英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：


请选择你想看的字典辞典：
单词字典翻译
derisum查看　derisum　在百度字典中的解释百度英翻中〔查看〕
derisum查看　derisum　在Google字典中的解释Google英翻中〔查看〕
derisum查看　derisum　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • The Quest for Herret Grips - The Firearms Forum
    Anyway got me a couple 5” light guns and wanted flat type grips on them Found that Herret made 1911 style grips for them at one time but were out of production So I paid $100 for a new set When they came I was happy with them they made gun feel like a 1911a1 Further research found that they also had made grips that were pure 1911
  • Pre-64 Winchester 94 breakdown info - The Firearms Forum
    I do the same as "The_Rifleman" for the barrel, but for the action, I use one of those reusable spray cans with Mineral Spirits I first clean the Barrel with sweets and Hoppe's Once that is clean I spray the action with spirits, then blast with compressed air I then use Rem Gun oil for the action, and Pure Tung Oil for the wood Excessive?
  • slugging my barrel - The Firearms Forum
    AR guy - the best cheapest and easiest way to slug a barrel that I use is to get a pure lead fishing sinker a little larger than your bore and tap it thru from the breach end with a wooden dowel Do not use steel or any other metal for this Remember that you want the softest purest lead you can find and sinkers are usually pure lead
  • Any Feedback on the Frankford Arsenal Pile Driver Bullet. . .
    That sure is a big piece of equipment for the actual task or perhaps it is just my visual perspective I had to pull a quantity of rounds and wore out a collet on the hammer system (as well as suffering pain) and while picking up a new collet and bought the RCBS puller die + 2 caliber specific collets and never looked back
  • Lee Hardness Tester Review Use | The Firearms Forum
    (Reserving the pure Pb for BP obsolete hunting bullets Figure I'd use a Lee Hardness Tester to adjust the mixture Downloaded some good info over at the Shooters Forum Cast Bullets on lead hardness but cant seem to find much technical info on the Lee tester
  • Linotype Lead Mixture - The Firearms Forum
    I would try 50 50 to start (1 2 pure, 1 2 lino) Linotype runs 21-22 BHN and pure lead is around 6 So a 50 50 alloy will be around 14 BHN which should be good for any handgun bullet I've mixed up a lot closer to 10-12 BHM for all my handgun shooting and as long as the bullets fit the barrel, leading is minimal
  • CZ70 Surplus Thoughts - The Firearms Forum
    Pure lead with an aluminum jacket hollow cavity Made for maximum expansion from a short barrel Aim small
  • Can you check lead Ingot hardness. . . - The Firearms Forum
    Wheel weights and similar alloys are usually soft enough to scratch with a thumb nail Pure lead is soft enough to indent with a thumbnail by pushing the nail straight in to the lead, you generally can't dent a wheel weight with your thumb nail by pushing it straight in even though if you drag your nail across it it will scratch it
  • Wood Stock care - The Firearms Forum
    Latest a Remington 513T made in 1940, no dings or scratches but some embedded oil and darkening from handling Cleaned with pure paint thinner, dried, first two applications were 50 50 mix of BLO turpentine to get into wood and grain followed by one coat of 25 75 turpentine BLO, and finally straight BLO Quite satisfied
  • Using zinc pennies in bullet casting? | The Firearms Forum
    The melting point of zinc is 787 2F whereas the melting point of lead is 621 5F - you certainly could melt the pennies and cast them but you'd have to heat them up much higher than lead The problem with the zinc pennies is that they aren't pure zinc The 1943 pennies were zinc coated steel and the melting point of steel is close to 2,000F





中文字典-英文字典  2005-2009