英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：


请选择你想看的字典辞典：
单词字典翻译
blasme查看　blasme　在百度字典中的解释百度英翻中〔查看〕
blasme查看　blasme　在Google字典中的解释Google英翻中〔查看〕
blasme查看　blasme　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Disabling firewall features on AT T Arris BGW210-700 Gateway
    I have an AT T Arris BGW210-700 gateway setup with IP Passthrough in front of my openwrt router Are these advanced options safe to disable with the default settings on openwrt’s firewall? Screenshot is the defaults but I want to turn them all off There’s also a toggle to enable the packet filter for the BGW210 which I have turned off
  • Default network and firewall configs - OpenWrt Forum
    Does someone know where to find the default network and firewall configs? I installed a custom image on the raspberry pi 4 to add USB ethernet and wifi drivers I made it work but I wonder if I set up the network and firewall correctly I found the git openwrt source but I can't find the default configs
  • How to set up firewall rules zones correctly for VLANs?
    Firewall > Traffic Rules > Add > Specify the source zone (that contains VLAN 10), the dest zone (containing VLAN5) and the destination IP (i e the QNAP's IP address) That specifically allows the traffic from VLAN10 to reach the QNAP However, this may only work for direct IP based connections and may not work for mdns zero-conf broadcast methods
  • Recommended firewall settings - Installing and Using OpenWrt Network . . .
    If you pull up Network>Firewall what are the recommended settings for "General" and "Zones?" Upon reading google hits, many are showing a "Lan -> wan" setting of "reject" for forward whereas the out-of-the-box settings have that set to "accept" including this OpenWRT wiki
  • How to reset OpenWrt firewall?
    Learn how to reset the OpenWrt firewall to its default initial state and rules
  • Firewall traffic log “live view” for rule debugging
    Are there any packages that may add visibility into firewall rule events (deny, allow) similar to the below?
  • Firewall: Multiple Source and Destination zones
    have to create 2 rule each for LAN (Main) and Guest Network even if they do they same thing foreach zone It would be nice to combine them into one Multiple Destination For example, Allow port 443 from lan to wan and vpn
  • How to block several outgoing ports in one firewall rule?
    I'm trying to add a firewall rule to block several outgoing ports, I'm only able to add two ports in the source port field - any more ports and a warning comes up
  • [SOLVED] Firewall status: active with no instances
    The firewall is operational (I know this because the device is behaving as it’s supposed to based on the firewall rules, including those I have put in) So I am wondering, what is the meaning of “active with no instances” in this context?
  • How to stop “reloading firewall due to ifup of modem”
    The firewall service reload should not cause connection reset Moreover, OpenWrt firewall depends on that reload to assign the zone properly Your issue is most likely due to the modem dropping connections by itself Unstable power, or too heavy load, or crappy firmware hardware, etc





中文字典-英文字典  2005-2009