英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：


请选择你想看的字典辞典：
单词字典翻译
avoids查看　avoids　在百度字典中的解释百度英翻中〔查看〕
avoids查看　avoids　在Google字典中的解释Google英翻中〔查看〕
avoids查看　avoids　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • TDA2: Termination Resistors on PCI-e TX and RX
    Is the a requirement for termination resistors on TX and RX for the PCI-e layout? This PCI-e bus is chip to chip not to an off board device I see in the recommended layout details for differential and single ended trace impedance
  • High-Speed PCB Layout for PCIe Gen 5 - Texas Instruments
    There is on-chip termination that activates after the Rx detect process is asserted on both inputs and outputs to facilitate signal integrity More importantly, PCIe Gen3 through Gen5 uses link training,
  • PCIe RX and REFCLOCK terminations - NVIDIA Developer Forums
    What is the internal terminations and biasing on PCIe RX Lines What i o standard is the PCIE REFCLOCK and does it have any terminations
  • Transceiver RX Termination : r FPGA - Reddit
    terminating to GND at the receiver is the most typical way to terminate If the resistor wasn't there, then like an ocean wave hitting a concrete wall, the voltage would rise above the normal positive voltage level at the receiver and be reflected back the transmission line has parasitic inductance
  • Solved: imx6sx pcie connection - NXP Community
    For pcie end device reference, I looked at the LAN7430 Datasheet, and it says that RX TX should use 0 1uF for AC coupling If I AC couple RX, how do I handle the termination resistor at the pcie rx input of i mx6SX?
  • PCI Express HCSL Termination AN-808 - Renesas Electronics Corporation
    datasheet for technical details The figure below represents the recommended source termination for applications using IDT low-power (9FGLxxx 9DBLxxx) or ultra low-power (9FGVxxx 9DBVxxx) series PCI Express Clock generators and buffers Figure 3 Termination for Applications using LP-HCSL or ULP-HCSL PCIe Clock Generators and Buffers
  • DS80PCI402 termination issues - Interface forum - TI E2E support forums
    Rx Detect is a feature used to detect the presence of a 50-Ohm termination AFTER the repeater Therefore, Rx detect is not checking that the repeater's Rx has detected anything (that definition pertains to "Signal Detect")
  • PCI Express – Signal Integrity and EMI - Microchip Technology
    With this termination scheme, you can unplug the connection and the signal waveform at the driver side does not change; unplugging causes no unwanted side effects For this reason, termination scheme 2 is preferred for HCSL for PCI Express systems
  • AM5726: PCIe termination resistor - TI E2E support forums
    No termination resistor seems to be placed on the AM572x EVM or AM572x IDK evaluation board No external termination resistors are needed on the TX RX pairs For PCIe, both the TX and RX pairs do need ac-coupling capacitors
  • Termination of unused mini PCIE lines on a USB only device
    Generally speaking, unused PCIe data lanes should be left unterminated This will apply to mini-PCIe as well PCIe transmitters use a receiver detection scheme which looks for a the termination impedance of the receivers to determine whether or not anything is connected





中文字典-英文字典  2005-2009